UK Monster Owners Club Forum » .: Technical :. » Mods & How To's » seized swinging arm on S4

Reply
 
Thread Tools Display Modes
Old 15-12-2019, 06:32 AM   #1
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
seized swinging arm on S4

when i put it back together in 2007 it was greased up well but now after removing retaining clips and 8mm clamp bolts and making a puller out of 10mm studding and applying masses of heat and penetrating oil and hammer force its not budging at all in fact the studding has snapped ,, going to try 12mm stud next the bearings and play are good but its got to come off for paint and polishing any ideas ??????
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 15-12-2019, 09:18 AM   #2
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,701
put a length of scaffolding pole between the bike and a substantial wall, then hammer it into the pole
slob is offline   Reply With Quote
Old 15-12-2019, 10:05 AM   #3
Mr Gazza
Lord of the Rings
 
Mr Gazza's Avatar
 
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,766
16mm studding.. Rattle gun .. Deep socket.
__________________
Mr Gazza is offline   Reply With Quote
Old 15-12-2019, 10:54 AM   #4
damien666
Registered User
 
Join Date: Dec 2010
Location: Leeds, West-Yorks
Bike: S4Rs
Posts: 497
https://www.ducatiforum.co.uk/thread...al-help.74577/
damien666 is offline   Reply With Quote
Old 15-12-2019, 12:40 PM   #5
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,009
Have you tried Plusgas?
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 15-12-2019, 07:17 PM   #6
Nickj
Too much time on my hands member
 
Nickj's Avatar
 
Join Date: Jun 2007
Location: Forest Of Dean
Bike: S2r
Posts: 3,187
Quote:
Originally Posted by slob View Post
put a length of scaffolding pole between the bike and a substantial wall, then hammer it into the pole
Precision engineering at it's finest I'd say.

Seems not an uncommon problem, I assume it's the shaft and bushes getting repeated hot cold cycles and able to suck in a little moisture?
__________________
"The final measure of any rider's skill is the inverse ratio of his preferred Traveling Speed to the number of bad scars on his body." Song of the sausage creature
Nickj is offline   Reply With Quote
Old 15-12-2019, 10:51 PM   #7
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
Quote:
Originally Posted by Darren69 View Post
Have you tried Plusgas?

loads of it
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 16-12-2019, 10:13 AM   #8
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
Its a double sided aluminium Swingarm,, 2 x 8mm clamp bolts and 2 circlips all removed arm is stuck on the hollow steel pin the biggest rod that goes thru is 14mm but even with that the puller has budged it 5mm afte 8 hours of heat and thumping and pulling ,,

It wont move any more im knackered and defeated

and plusgas is £9 a small tin here and no brass drifts availabe larger than 8 mm
im losing heart
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 16-12-2019, 10:27 AM   #9
mickj
Registered User
 
mickj's Avatar
 
Join Date: Jun 2018
Location: Clevedon
Bike: M1200s
Posts: 550
Diesel is only £1.27 a ltr, does a good job as a penetrating oil.
__________________
Keep the rubber side down. Mick
mickj is offline   Reply With Quote
Old 16-12-2019, 01:05 PM   #10
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
Quote:
Originally Posted by mjgt View Post
Diesel is only £1.27 a ltr, does a good job as a penetrating oil.

its only 60p a litre here i forgot diesel will do thanks but im getting a brass mandrel made up 14mm shaft to 17mm shank and a bigger hammer
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 16-12-2019, 04:32 PM   #11
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
Quote:
Originally Posted by jerry View Post
its only 60p a litre here i forgot diesel will do thanks but im getting a brass mandrel made up 14mm shaft to 17mm shank and a bigger hammer
I think I have one i made but is not brass for my s4 in 2008. I just made it with about 0.10 clear.
Albie is offline   Reply With Quote
Old 17-12-2019, 03:49 AM   #12
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
i measured it up with micrometer the shaft is 19.98mm outside so will make the mandrel 19.7mm,, with a extension of 14mm to go in the hollow centre of the shaft as a locator
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 21-12-2019, 02:06 AM   #13
jerry
Old Git
 
jerry's Avatar
 
Join Date: May 2006
Location: Cricklade
Bike: Multiple Monsters
Posts: 2,793
got a mandrel now been dosing it with diesel , atf and acetone for 4 days ,, still wont budge at all
__________________
MONSTERMAN
jerry is offline   Reply With Quote
Old 21-12-2019, 12:03 PM   #14
Martin Duke
Member
 
Join Date: Jul 2011
Location: Wells
Bike: Multiple Monsters
Posts: 110
Penetrating fluids

Quote:
Originally Posted by Darren69 View Post
Have you tried Plusgas?
This may help - I collect and restore old model aircraft engines, some of my older examples were built in the 1930's. I'm often dealing with seized and corroded parts, however on a web site I use there was an experiment to find the best fluid for freeing rusted parts and the absolute best (far better than anything available commercially) was a mix of acetone and automatic transmission fluid, 50/50.

I can try and find the link if anybody is interested.

Martin
Martin Duke is offline   Reply With Quote
Old 21-12-2019, 11:01 PM   #15
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,009
Do you have it on it's side so the fluid can flow down into it? I'm just wondering if maybe a bearing has broken up and is jamming things up. Sorry I can't be more helpful at this point as I've not ever removed one before. Just thinking out aloud, but maybe I should shut up?
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:13 AM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.