Monster Project (Refresh) - Page 2

spacemonkey · 28-09-2014, 09:41 PM

That looks quite mean and moody, a lot better than I was expecting!

Yorkie · 04-10-2014, 08:03 PM

Dropped the Monster off at MADASL ready for today's strip down.

And so it starts:

Still not 100% what I'm going to do (apart from the ST2 engine). Cheers to Mark at http://www.madasl.co.uk/ for all the help.

Yorkie

Yorkie · 25-10-2014, 07:10 PM

No more progress on the Monster, but the ST2 is now fully stripped down so the engine prep can start.

Yorkie

Yorkie · 25-10-2014, 07:35 PM

All I am looking out for now is the following to pimp it out:

1100 Crank
1000DS Pistons/crank

I you know of any of the above, that would be great.

Yorkie

Yorkie · 25-10-2014, 09:15 PM

I also got hold of a set of Triumph clip-ons they just need to be milled out to 50mm to fit I think, even doing that is a lot cheaper than any Ducati marked bits.

Yorkie

Saint aka ML · 25-10-2014, 09:30 PM

Quote:

Originally Posted by Yorkie

All I am looking out for now is the following to pimp it out:

1100 Crank
1000DS Pistons/crank

I you know of any of the above, that would be great.

Yorkie

What is the benefit? The major restriction on old 900 are the heads not crank/pistons.

Yorkie · 25-10-2014, 09:36 PM

They are for the ST2 engine mate, I think it takes it from 944 to 992 approx.

Yorkie

spacemonkey · 25-10-2014, 10:27 PM

Do you need to remove the sprockets the belts run on in the heads to be able to remove the black rubber bits the belt covers screw onto? My covers and the rubber bits need replacing as does the paint all over... so I guess I'd need that special tool to remove the sprockets? Can you turn the engine using that tool with the belts on to TDC if the plugs are out?

Yorkie · 25-10-2014, 11:05 PM

The cam wheels do need to be removed to get the plastic bit off.

You should be able to turn the engine over, but I have not tried it.

If you are going to do I would wait until you belts need doing.

Yorkie

spacemonkey · 28-10-2014, 02:20 PM

I'm taking the heads and barrels off to repaint the block in the frame, do the valve guide oil seals, barrel/base oil seals and the belts. The engine hasn't turned in 5 years.... I want to put it to TDC first. I suppose I could use the chain sprocket to turn it, but to paint properly, the plastics have to some off and the horizontal one could do with replacing anyway. Right, I'll order the tool.

Yorkie · 28-10-2014, 04:59 PM

If you want the horizontal one and the ST2 one fits you can have it. Again I am running mine totally without.

Yorkie

spacemonkey · 28-10-2014, 05:01 PM

Yes please! I'm looking to replace any of the bits of the belt covers for both cylinders so any spare bits would be VERY appreciated!! I'll pm you my details and let me know how much you want.

Yorkie · 01-11-2014, 06:40 PM

Today I mostly did this:

The flywheel weighs a lot, so its getting chopped:

Lots of spinning gear things that fell out:

The rest ...... it just fell apart:

Yorkie

02-11-2014, 11:28 AM

A early 748 flywheel works well on a st2 engine!

Yorkie · 02-11-2014, 11:36 AM

Cheers 888.

It will work out cheaper getting all the bits I have (flywheel, primary gears etc) milled and drilled to make them lighter, then a balanced crank set up.

I just need the 1000ds pistons or 944 hi-comps to finish the top end.

Yorkie

28-09-2014, 09:41 PM	#16
spacemonkey I see dead people. Join Date: May 2003 Location: Carving a slice thru the braindead masses..(pun intended) Bike: M900 Posts: 1,464	That looks quite mean and moody, a lot better than I was expecting! __________________ http://www.jasperfforde.com/swindon/7wonders.html

04-10-2014, 08:03 PM	#17
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	Dropped the Monster off at MADASL ready for today's strip down. And so it starts: Still not 100% what I'm going to do (apart from the ST2 engine). Cheers to Mark at http://www.madasl.co.uk/ for all the help. Yorkie __________________ NO ICE, GUN IT!

25-10-2014, 07:10 PM	#18
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	No more progress on the Monster, but the ST2 is now fully stripped down so the engine prep can start. Yorkie __________________ NO ICE, GUN IT!

25-10-2014, 07:35 PM	#19
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	All I am looking out for now is the following to pimp it out: 1100 Crank 1000DS Pistons/crank I you know of any of the above, that would be great. Yorkie __________________ NO ICE, GUN IT!

25-10-2014, 09:15 PM	#20
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	I also got hold of a set of Triumph clip-ons they just need to be milled out to 50mm to fit I think, even doing that is a lot cheaper than any Ducati marked bits. Yorkie __________________ NO ICE, GUN IT!

25-10-2014, 09:36 PM	#22
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	They are for the ST2 engine mate, I think it takes it from 944 to 992 approx. Yorkie __________________ NO ICE, GUN IT!

25-10-2014, 10:27 PM	#23
spacemonkey I see dead people. Join Date: May 2003 Location: Carving a slice thru the braindead masses..(pun intended) Bike: M900 Posts: 1,464	Do you need to remove the sprockets the belts run on in the heads to be able to remove the black rubber bits the belt covers screw onto? My covers and the rubber bits need replacing as does the paint all over... so I guess I'd need that special tool to remove the sprockets? Can you turn the engine using that tool with the belts on to TDC if the plugs are out? __________________ http://www.jasperfforde.com/swindon/7wonders.html

25-10-2014, 11:05 PM	#24
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	The cam wheels do need to be removed to get the plastic bit off. You should be able to turn the engine over, but I have not tried it. If you are going to do I would wait until you belts need doing. Yorkie __________________ NO ICE, GUN IT!

28-10-2014, 02:20 PM	#25
spacemonkey I see dead people. Join Date: May 2003 Location: Carving a slice thru the braindead masses..(pun intended) Bike: M900 Posts: 1,464	I'm taking the heads and barrels off to repaint the block in the frame, do the valve guide oil seals, barrel/base oil seals and the belts. The engine hasn't turned in 5 years.... I want to put it to TDC first. I suppose I could use the chain sprocket to turn it, but to paint properly, the plastics have to some off and the horizontal one could do with replacing anyway. Right, I'll order the tool. __________________ http://www.jasperfforde.com/swindon/7wonders.html

28-10-2014, 04:59 PM	#26
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	If you want the horizontal one and the ST2 one fits you can have it. Again I am running mine totally without. Yorkie __________________ NO ICE, GUN IT!

28-10-2014, 05:01 PM	#27
spacemonkey I see dead people. Join Date: May 2003 Location: Carving a slice thru the braindead masses..(pun intended) Bike: M900 Posts: 1,464	Yes please! I'm looking to replace any of the bits of the belt covers for both cylinders so any spare bits would be VERY appreciated!! I'll pm you my details and let me know how much you want. __________________ http://www.jasperfforde.com/swindon/7wonders.html

01-11-2014, 06:40 PM	#28
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	Today I mostly did this: The flywheel weighs a lot, so its getting chopped: Lots of spinning gear things that fell out: The rest ...... it just fell apart: Yorkie __________________ NO ICE, GUN IT!

02-11-2014, 11:28 AM	#29
888 Guest Posts: n/a	A early 748 flywheel works well on a st2 engine!

02-11-2014, 11:36 AM	#30
Yorkie Anglo-Saxon Warrior Join Date: Aug 2002 Location: North Yorkshire Bike: M900 Posts: 2,485	Cheers 888. It will work out cheaper getting all the bits I have (flywheel, primary gears etc) milled and drilled to make them lighter, then a balanced crank set up. I just need the 1000ds pistons or 944 hi-comps to finish the top end. Yorkie __________________ NO ICE, GUN IT!