Register | FAQ | Members List | Calendar | Today's Posts | Search | Contact |
|
Registered
Members: 601 | Total Threads: 50,794 | Total Posts: 518,310 Currently Active Users: 789 (0 active members) Please welcome our newest member, Foggy |
|
|
Thread Tools | Display Modes |
11-07-2022, 04:45 PM | #1 |
Registered User
Join Date: Jun 2015
Location: Livingston
Bike: M1100evo
Posts: 863
|
Cush drive and sprocket carrier
Hi guy’s,
Been having a chain issue recently. Upon investigation I’ve found that my sprocket carrier has been moving laterally maybe 3/4mm + the maybe 2mm that the chain moves laterally also. So I’ve taken it all apart and put it all back together (hand tight for the moment) and the cush drive/sprocket carrier lateral movement has gone! Only the 2mm chain movement remains. Is this correct? Or should the sprocket carried have some movement? Also does the cush drives need lubed before going back in and able to rotate when tightened up? Or does the nut/bolt/cush drive hex assembly need to be tightened to a specific torque value, which would necessitate the need to buy a 12mm hex key?!?! Thanks again troops. Last edited by Ron1000; 11-07-2022 at 05:04 PM.. |
14-07-2022, 09:09 AM | #2 |
Registered User
Join Date: Jun 2015
Location: Livingston
Bike: M1100evo
Posts: 863
|
This thread doesn’t seem to have set the heater on fire
From my own research it looks as if there should be no lateral movement in the sprocket carrier and hub assembly. So M12 hex key ordered and I’ll torque it down to 48?nM. Can anybody confirm that torque setting. I’ll also re-fit the sprocket and tighten down to 18?nM The main nut is simple. |
14-07-2022, 10:58 AM | #3 |
.
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,712
|
Sorry James, I missed this.
No (or minimal) lateral movement would be good! 48Nm sounds right, Vince hasn't posted anything here http://ukmonster.co.uk/monster/showthread.php?t=58281 re: mistakes around the rear wheel. I'm not sure where your 18Nm comes from. I assume you're working from the evo manual? |
14-07-2022, 11:59 AM | #4 |
Registered User
Join Date: Jun 2015
Location: Livingston
Bike: M1100evo
Posts: 863
|
18nM comes from renthal for the sprocket carrier i’ve got.
|
14-07-2022, 10:07 PM | #5 |
Registered User
Join Date: Dec 2010
Location: Oslo
Bike: S2r
Posts: 426
|
I recently replaced my carrier, after too many km. It was moving 10-15 mm sideways like a drunken sailor. Despite a new'ish flange it was all over the place. The nice red cush drives were all broken (bolt separated from plastic) and most of the cush retaining tabs also gone.
I'm assuming you're half way there. My final test was to check for play between carrier and flange. Should be quite tight. Was NOT. Some play good to allow for twisting while under/off load, but probably not enough for you to discover using hand force. |
19-07-2022, 02:46 PM | #6 |
Registered User
Join Date: Jun 2015
Location: Livingston
Bike: M1100evo
Posts: 863
|
Ok so new 12mm hex socket arrived. Everything is refitted, correctly torqued, chain on with correct slack and eccentric adjusters correctly tightened.
It’s significantly better with only 0.5mm to 1mm of lateral movement. Cush drives look ok to me but I’ve zero experience in them tbh. I’ve also inspected the chain for more rubber ‘hairs’. None atm. I think I’ll ride it as is (only got 750 miles until it hits a desmo service) at which point I’ll discuss with the ducati dude. |
|
|