UK Monster Owners Club Forum » Gallery » UKMOC Bikes » Back with a M900 series I

Reply
 
Thread Tools Rating: Thread Rating: 8 votes, 5.00 average. Display Modes
Old 04-03-2022, 03:00 PM   #571
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
Getting started as it's raining no work for me to volunteer too.

Albie is offline   Reply With Quote
Old 04-03-2022, 04:57 PM   #572
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,009
Nice garage art too!
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 11-03-2022, 10:04 PM   #573
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
dry run

Having little to do but reassure myself parts are clean and not missing I started more dry assembly making sure all bolts are in correct holes and lengths, I made a note in my workshop fiche of lengths especially those m6 ones in valve covers and belt covers.
I so wish my frame was done but its not so just preparing everything better than last time and sorting the clutch reservoir someone commented my was later, They were of course correct bloody rivet counters but most would never see it. Its literally a small radius where the piston pin goes in.
I fitted the throttle cables attached to the twist grip this time before carbs on, Last time it was reverse and gynaecology came to mind.
Everything is going well though and rather more satisfying this time.



Albie is offline   Reply With Quote
Old 13-03-2022, 08:06 PM   #574
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
Dry run ptII

A good day today sorting bolts and bagged stuff making sure everything clean and had a home. A few swapped bits like bolts etc and changed my decent headlight frame bracket for a NOS gifted to me one. Fitted the good breather pipes I got from Paranoid Dave and warmed up the end to soften it as they easily crack or split. Took a while to find the cover caps for the handlebar clamp bolts as they were in the rubber band straps bag.
Unfortunately I have come to the end of the dry run so Im going to have to get the credit card out and get the frame blasted and buy paint and sprayed as soon as I can. I shall make enquiries tomorrow fro paint and spraying. I have already costed the blasting @ £68 plus vat but I have to go for broke now I am too far in to stop now.



note pic above 1 bolt is a cheese ended one at 5mm longer. I changed from a normal allen head after viewing fiche.



Pic above the very rare early numberplate light unit only used for short time as Ducati redesigned I tas we all know it now with no screws showing. Mind you its easier on this type to change the bulb and far less crap.










Last edited by Albie; 13-03-2022 at 08:13 PM..
Albie is offline   Reply With Quote
Old 13-03-2022, 08:40 PM   #575
Jez900ie
Pleasantly surprised!
 
Jez900ie's Avatar
 
Join Date: Nov 2016
Location: Stoke on Trent
Bike: M900ie
Posts: 780
I don't think I've ever seen such a clean machine. Good work Albie!
__________________
Monsters don't hide under the bed, they sleep inside the shed
Jez900ie is offline   Reply With Quote
Old 16-03-2022, 09:17 AM   #576
Christy
Registered User
 
Christy's Avatar
 
Join Date: Jan 2012
Location: Hull
Bike: M900
Posts: 75
Looking good Albie. Mine has the two screw number plate light. Not the steel number plate bracket through. Not noticed that before.
__________________
Keeping it real
M900 (93), Multistrada 950, 900SS Project, Guzzi Breva 1100
Christy is offline   Reply With Quote
Old 16-03-2022, 10:27 AM   #577
Dukedesmo
Registered User
 
Dukedesmo's Avatar
 
Join Date: Sep 2010
Location: Leics
Bike: M900
Posts: 2,828
Quote:
Originally Posted by Christy View Post
Looking good Albie. Mine has the two screw number plate light. Not the steel number plate bracket through. Not noticed that before.
I think the steel plate is designed for Italian number plate fitment, that use 4 corner holes to hold the plate on.

Both my 916 and Guzzi had them fitted but I removed them as (to me) they're just unnecessary added weight.
__________________
M900, 916, LeMans II.

Dukedesmo is offline   Reply With Quote
Old 16-03-2022, 08:07 PM   #578
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
Quote:
Originally Posted by Dukedesmo View Post
I think the steel plate is designed for Italian number plate fitment, that use 4 corner holes to hold the plate on.

Both my 916 and Guzzi had them fitted but I removed them as (to me) they're just unnecessary added weight.


I work from the original fiche whether or not that's right or wrong. It's still the same on Ducati parts too. Weight saving doesnt come into my world much on resto. It's a solid fix no flapping around as it's also aluminium number plate on mine. Ooh weight save.

I got my clutch seal kit yesterday and tomorrow I have no necessary work at the garage so can do my stuff. Today I did belts and valve checks etc on a nice 848. Having a ball in fact it's a real pleasure. .l
Albie is offline   Reply With Quote
Old 16-03-2022, 08:15 PM   #579
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
It also seems the Italians were lucky to get different braking on the rear.



indian baby boy names 2019
Albie is offline   Reply With Quote
Old 17-03-2022, 07:03 PM   #580
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
This afternoon I took on the task of replacing the insides of the replacement clutch master . Petty I know but I only changed it because it was a 2005 one and a rivet counter told me. It's such a small detail but it matters. Its 2 things as in the older has a radius on banjo fitting end and the reservoir top has bigger lettering and also a elephant on the bottom. A managed to get a PS13 kit thats 13mm piston and had to change this because the rubber cover was split and untidy. I removed the sight window and cleaned that as was dirty and yellowed but now clean. Before that it had a repaint too. It's not difficult to change the seals but there is very little info out there but common sense and care will get you there if you are safe to attempt this stuff. I followed this guys advice....
http://forums.ducatipaso.org/viewtopic.php?t=8289
It all work great following his knowledge. I also painted the brake one but I had a lucky escape because when I went to fit brake lever to it the piston was trying to push out. The circlip on this 15mm piston one had either not been fitted properly before or had crept out I dont know how mind. I took it apart and it was all there and after a thorough clean I reassembled it as it should be and now working as it should by hand. If it leaks I will order a new kit for that too. Fitted back the brake switch so now I just have to respray the other lid to swap it over.





[url=https://postimg.cc/rdHrCZmj][/ur






Last edited by Albie; 17-03-2022 at 07:06 PM..
Albie is offline   Reply With Quote
Old 18-03-2022, 09:16 AM   #581
the lodger
Registered User
 
the lodger's Avatar
 
Join Date: Oct 2019
Location: Chorley
Bike: M900
Posts: 160
Anorak alert ! (Is there an emoji for this I wonder ? ).

Note the cylnder cap wording refers to using only dot 3+5 fluid from a sealed container. Well you can't mix dot 3 and dot 5 as the latter is a mineral oil and doesn't mix with dot 3.

You could use dot 5 if all the brake components were new . I wonder if this is what Ducati or Brembo were thinking when making the set-up but I doubt it and I think it's just an error. Later caps just refer to using dot 4.
__________________
Contents may settle !
the lodger is offline   Reply With Quote
Old 18-03-2022, 10:08 AM   #582
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,009
because we're all anoraks really?
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 18-03-2022, 10:19 AM   #583
Flip
Registered User
 
Flip's Avatar
 
Join Date: Mar 2010
Location: Beachtown
Bike: M900
Posts: 2,188
Quote:
Originally Posted by the lodger View Post
Anorak alert ! (Is there an emoji for this I wonder ? ).

Note the cylnder cap wording refers to using only dot 3+5 fluid from a sealed container. Well you can't mix dot 3 and dot 5 as the latter is a mineral oil and doesn't mix with dot 3.

You could use dot 5 if all the brake components were new . I wonder if this is what Ducati or Brembo were thinking when making the set-up but I doubt it and I think it's just an error. Later caps just refer to using dot 4.
My understanding is that Brake fluids are Glycol based not mineral with the exception of DOT 5 (not to be confused with DOT 5.1) which is Silicone based.

Glycol absorbs water (Hygroscopic) while Silicone repels it (Hydrophobic) hence why you shouldn’t use DOT 5 if the system has previously been filled with Glycol based fluid and why they cannot be mixed.
__________________
You're perfect, yes, it's true- But without me you're only you!
Flip is offline   Reply With Quote
Old 18-03-2022, 12:06 PM   #584
Albie
Fanactical volunteer
 
Albie's Avatar
 
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,028
Quote:
Originally Posted by the lodger View Post
Anorak alert ! (Is there an emoji for this I wonder ? ).

Note the cylnder cap wording refers to using only dot 3+5 fluid from a sealed container. Well you can't mix dot 3 and dot 5 as the latter is a mineral oil and doesn't mix with dot 3.

You could use dot 5 if all the brake components were new . I wonder if this is what Ducati or Brembo were thinking when making the set-up but I doubt it and I think it's just an error. Later caps just refer to using dot 4.
Dont worry I wont be using or searching for dot3.
Albie is offline   Reply With Quote
Old 18-03-2022, 12:20 PM   #585
Luddite
Registered User
 
Luddite's Avatar
 
Join Date: Aug 2011
Location: Southampton
Bike: M1100evo
Posts: 2,465
Quote:
Originally Posted by the lodger View Post
Anorak alert ! (Is there an emoji for this I wonder ? ).

Note the cylnder cap wording refers to using only dot 3+5 fluid from a sealed container. Well you can't mix dot 3 and dot 5 as the latter is a mineral oil and doesn't mix with dot 3.

You could use dot 5 if all the brake components were new . I wonder if this is what Ducati or Brembo were thinking when making the set-up but I doubt it and I think it's just an error. Later caps just refer to using dot 4.
There was a post about this on the Ducati Sporting Club forum way back.

https://www.ducatisportingclub.com/s...ead.php?t=2521
Luddite is offline   Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:52 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.