UK Monster Owners Club Forum » .: Technical :. » Kits & Accessories » 937 headstock stand

Reply
 
Thread Tools Display Modes
Old 08-04-2024, 10:41 AM   #1
MarkArbroath
Junior Member
 
Join Date: Feb 2024
Location: Arbroath
Bike: Monster 950
Posts: 5
937 headstock stand

Does anybody have a headstock stand for their Monster 937 and if so which make? Thinking of one but looks like the headlight sits too low, and it’s a pain to take the headlight off!
TIA
Mark
MarkArbroath is offline   Reply With Quote
Old 09-05-2024, 09:02 AM   #2
dunf
Registered User
 
dunf's Avatar
 
Join Date: Jan 2022
Location: Dunfermline
Bike: M1200s
Posts: 32
Quote:
Originally Posted by MarkArbroath View Post
Does anybody have a headstock stand for their Monster 937 and if so which make? Thinking of one but looks like the headlight sits too low, and it’s a pain to take the headlight off!
TIA
Mark
I have a generic headstock stand and it doesn't fit my M1200 due to the headlight position so you might well be correct.
dunf is offline   Reply With Quote
Old 09-05-2024, 10:35 AM   #3
Mr Gazza
Lord of the Rings
 
Mr Gazza's Avatar
 
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,963
I've got a bike with one of those trendy modern melted headlamps and my stem stand crunches it! I've only tried it once and got away with it, but it aint right by a large margin.

I plan to get a pin made with a longer shoulder to push the stand arm lower. That will of course make it tighter on the mudguard, but I'll take that off as a precaution when using the stand.

I might be able to get away with some large washers or a spacer of some sort if I have a closer look, but that will rob from the pin length that goes into the stem and this is where a stem stand gets it's rigidity.

The worst part of it all is that I have the latest Showa forks which are asymmetric, making a front paddock stand impossible to use. The fork bottoms are different heights and shapes. They have a spring in one leg and all the damping in the other.
Even getting the pin in the stem is not straightforward as the front brake lines tee there to go to the ABS unit and the bracket blanks the stem hole.. Progress eh?
__________________

Last edited by Mr Gazza; 09-05-2024 at 10:49 AM..
Mr Gazza is offline   Reply With Quote
Old 09-05-2024, 12:11 PM   #4
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
good spot with the spring/damping gaza.
cagiva mitos were famous for falling over while you changed a front tyre, as the damper conpressed, if left with the spindle out.

i’d be happy to turn an alternate pin if anyone wants to send me some accurate measurements.
slob is offline   Reply With Quote
Old 09-05-2024, 07:57 PM   #5
Mr Gazza
Lord of the Rings
 
Mr Gazza's Avatar
 
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,963
I've just had a play with my Constands headstock stand.
It turns out that I don't have the correct size pin for that bike. The Monster works great with an 18mm pin, but has a proper round headlamp.

The other one has a 14mm internal diameter stem and I have been using a 13mm pin which is too sloppy and lets the arm pivot enough to contact the headlamp assy.

In my case turning the 15mm pin down to fit should cure the problem I think?
It doesn't look like any extra pin length would be needed if it were tighter in my case.

There is a huge compatibility list on the Constands site, so I guess it's a mater of searching for one that is listed as fitting.. Sorry the list is too long for me to trawl through. Maybe you could drop them a line?
A good start would be to measure the internal diameter of your stem.

I have the Constands 5 pin model which is very good, even if it doesn't have quite the right pin for one of my bikes, but I'd recommend the stand and it's easy to modify a pin.
__________________

Last edited by Mr Gazza; 09-05-2024 at 08:00 PM..
Mr Gazza is offline   Reply With Quote
Old 17-05-2024, 05:15 PM   #6
Mr Gazza
Lord of the Rings
 
Mr Gazza's Avatar
 
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,963
Just to bring tis up to date; I took an oversized pin to my mate this morning and he turned it down to a snug fit fit in my stem while I waited.
The result is much more successful than I hoped for.
By making a pin fit properly, the arm retains the correct geometry it was designed for and clears the headlamp by a good margin.
Just looking at pictures of the 937, I think the headlamp on my bike sits lower in relation to the bottom yoke than on the 937.

I do have to take my front mudguard off to get the stand in place, but it's a very wide and flat design. Note to motorcycle designers; we need longer mudguards behind the forks not wider ones!)

So certainly a Constands 5 pin front stand is going to work, provided you get a pin to fit snugly, either by turning one down to suit or buying a suitable one.
__________________
Mr Gazza is offline   Reply With Quote
Old 18-05-2024, 01:04 AM   #7
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,091
Why deal with all this madness if you can get and Abba stand it will do all that and more? I can remove the entire front or rear of the bike with that thing, not at the same time and dont need no ST centre stand dead weight either.
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT. The time now is 10:53 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.