Register | FAQ | Members List | Calendar | Today's Posts | Search | Contact |
|
Registered
Members: 673 | Total Threads: 50,934 | Total Posts: 519,365 Currently Active Users: 1,129 (0 active members) Please welcome our newest member, Mozzer46 |
|
|
Thread Tools | Rate Thread | Display Modes |
30-08-2020, 03:18 PM | #16 |
.
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
|
now’s a good time to check the swingarm bearings...
another pita job to do while the engine’s seperated from the frame |
30-08-2020, 03:19 PM | #17 |
.
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
|
Well done.
I see you’ve still got the original oil level plate/sticker. Look after that as no longer available, the new ones are noticeably different.
__________________
Original and Best since 1993 |
30-08-2020, 05:39 PM | #18 |
Guest
Posts: n/a
|
|
31-08-2020, 02:09 AM | #19 | |
No turn left unstoned
Join Date: Jun 2010
Location: leicester
Bike: M750
Posts: 4,559
|
Quote:
Most important is probably to get the drilling absolutely dead central, which is far more difficult than it sounds because the threads of the old bit of stud deceive your eye. Also to drill perfectly perpendicular. The initial centrepunch dot is extremely important to get as near to perfectly central as possible. Then following that up with either a centre-drill (preferably) or a small plain drill is essential before getting out the bigger drills. When you do employ a bigger drill it might be worth considering buying a suitably sized lefthand drill as this will tend to unscrew the broken stud as it cuts. Before doing any of this, I would give the stud a good few sharp blows with a hammer and punch in an attempt to jar loose any corrosion or binding in the threads .. followed by a good soak in decent penetrating oil. Also worth considering is a lefthand tap and matching bolt to use as an extraction device. And also the application of heat. Obviously enough, a drill will tend to favour wandering off and cutting into the softer ally of the case rather than the hard steel of the stud. If the stud is stainless (or even if its not) a slow drilling speed, plenty of axial pressure and copious cutting oil will produce the best drilling performance. Sorry if any of that is granny egg-sucking info but better to mention than not, I reckon. And welcome along. |
|
31-08-2020, 10:12 AM | #20 | |
Guest
Posts: n/a
|
Quote:
If it doesn't look like it's going to work then I will stop before I totally balls it up and split the cases and find a local engineering shop. |
|
08-09-2020, 08:06 AM | #21 |
Registered User
Join Date: Jul 2011
Location: Dundee
Bike: M900ie
Posts: 299
|
Hi and welcome. Looking forward to seeing the rebuild as it progresses. Good luck.
__________________
Ripsnorting |
10-09-2020, 10:53 AM | #22 |
Guest
Posts: n/a
|
So a little update for you.
The drilling of the broken stud went exactly as I thought it would. So I am now stripping the cases to get the broken bit spark eroded out. However that has been fraught with problems. First the clutch hub nut would not come off. My old impact gun wasn't man enough neither was my socket which broke. So enter the new Milwaukee impact gun. What a beast. That and the new socket made light work of it. Being the LH case means I'm now awaiting the primary gear puller as the trusty 2 leg simply won't fit no matter how much modification. In the mean time the wheels are at the powder coaters, frame and bodywork are at the paint shop so there is some progress. |
10-09-2020, 11:37 AM | #23 |
.
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
|
r/h case?
the primary gear can be a proper arse, sometimes they practically fall off other times you find yourself hitting the puller bolt with a hammer before it moves. case split is a good excuse for new main bearings and a crankshaft sludge-trap cleanout. Last edited by slob; 10-09-2020 at 11:40 AM.. |
10-09-2020, 04:52 PM | #24 |
Guest
Posts: n/a
|
|
10-09-2020, 05:09 PM | #25 |
.
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
|
I like the teacup
|
10-09-2020, 05:27 PM | #26 |
.
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
|
__________________
Original and Best since 1993 |
10-09-2020, 05:36 PM | #27 |
.
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
|
APE replacement studs?
|
10-09-2020, 10:34 PM | #28 |
Guest
Posts: n/a
|
Haha yup APE studs and the tea cup is my work mug and censored. Check out the lovely Kayleigh at Pocket Perfect Designs for suitably rude drinkware.
|
14-09-2020, 06:27 PM | #29 |
Guest
Posts: n/a
|
|
24-10-2020, 10:53 AM | #30 |
Guest
Posts: n/a
|
So it's been a while but here are some update snaps. Its heading the right way now although I'm sure there will be a hundred little jobs cropping up. I snapped a bloody oil ring getting the front cylinder on (only 2nd time I've ever done that) so that was a costly mistake. I found the good fellows at Motorapido to be excellent to deal with for parts.
[IMG][/IMG] [IMG][/IMG] [IMG][/IMG] |
|
|