UK Monster Owners Club Forum » .: Technical :. » Engines, Clutch, Gears » Monster 900 ie troubles

Reply
 
Thread Tools Display Modes
Old 04-09-2005, 05:09 PM   #1
blueguzzi
Junior Member
 
Join Date: Jan 2005
Location: Southend -on-Sea
Bike: M900ie
Posts: 53
Unhappy Monster 900 ie troubles

Ok so i was bimbling a long when suddenly cough splutter it starts running rough and now will not tick over when coming to a halt, it needs more throttle just to keep it running.
I have changed the fuel filter and fitted new plugs, i noticed the old plugs were black as in running rich?
It still will not run correctly.
I have checked that the throttle butterfly valves open and close ok and seem good with the choke as well.
Hmmm any clues?
I reckon there is a sensor somewhere thats giving incorrect readings?
Any ideas or suggestions will be appreciated.
ta
Hugh
blueguzzi is offline   Reply With Quote
Old 04-09-2005, 05:37 PM   #2
tommo
Guest
 
Posts: n/a
sounds like it could be something like a blocked or miss firing injector but not sure, i had the same type of problem on my 600 but mine has carb's and the poor running was down to a faulty plug lead.
  Reply With Quote
Old 04-09-2005, 06:04 PM   #3
fatbloke
Guest
 
Posts: n/a
sounds a lot like a problem gary had, it was found to be the sensor
mounted on top of the front cylinder (marked 32 on pic)

if its any help the part No is 552.4.013.1A.
  Reply With Quote
Old 04-09-2005, 06:23 PM   #4
Starter Sprag
Guest
 
Posts: n/a
Running rough

Quote:
Originally Posted by blueguzzi
Ok so i was bimbling a long when suddenly cough splutter it starts running rough and now will not tick over when coming to a halt, it needs more throttle just to keep it running.
I have changed the fuel filter and fitted new plugs, i noticed the old plugs were black as in running rich?
It still will not run correctly.
I have checked that the throttle butterfly valves open and close ok and seem good with the choke as well.
Hmmm any clues?
I reckon there is a sensor somewhere thats giving incorrect readings?
Any ideas or suggestions will be appreciated.
ta
Hugh
Check your air filter is ok

The sensor gets full of water and corrodes the two pins, give them a good clean with a tooth brush and wd-40, dry off and liberally grease up, couple up connection and wipe off excess grease
  Reply With Quote
Old 04-09-2005, 07:09 PM   #5
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
Quote:
Originally Posted by fatbloke
sounds a lot like a problem gary had, it was found to be the sensor
mounted on top of the front cylinder (marked 32 on pic)

if its any help the part No is 552.4.013.1A.
And Benson.
slob is offline   Reply With Quote
Old 04-09-2005, 07:14 PM   #6
fatbloke
Guest
 
Posts: n/a
and all 3 bikes are the same year I think I can see a pattern forming
  Reply With Quote
Old 04-09-2005, 08:52 PM   #7
gary tompkins
1/2 man - 1/2 pogo-stick
 
gary tompkins's Avatar
 
Join Date: Aug 2002
Location: Dartford, Kent
Bike: M900ie
Posts: 7,241
Temperature sensor

Yep - seems common to 2001-2001 900ie's. Woody (DWR) said he's heard of other temp. sensors packing up, but most result in ECU providing no fuel at all so the bike won't start. Mine was telling the ECU the engine was colder than it was and making it run really rich. It was a sod to start and wouldn't tick over at all.
__________________
GT
Fully paid up member of the S.A.S. (Scottoiler Appreciation Society) 27,000 miles on original chain - and still going strong!
gary tompkins is offline   Reply With Quote
Old 04-09-2005, 10:10 PM   #8
blueguzzi
Junior Member
 
Join Date: Jan 2005
Location: Southend -on-Sea
Bike: M900ie
Posts: 53
Smile

Quote:
Originally Posted by gary tompkins
Yep - seems common to 2001-2001 900ie's. Woody (DWR) said he's heard of other temp. sensors packing up, but most result in ECU providing no fuel at all so the bike won't start. Mine was telling the ECU the engine was colder than it was and making it run really rich. It was a sod to start and wouldn't tick over at all.
Ah Yes Mr Gary T thats just what is happenning! So ecu is getting dodgy messages from a confused temp sensor.
Many Thanks everyone for the advice.
According to the Ducati Spares description this part is a
'water temperature sensor' that must be why its confused as it has'nt rained for a while and has no water to operate in!!!!!!!!! :lol: :lol:

cheers all
Hugh
blueguzzi is offline   Reply With Quote
Old 04-09-2005, 11:57 PM   #9
gary tompkins
1/2 man - 1/2 pogo-stick
 
gary tompkins's Avatar
 
Join Date: Aug 2002
Location: Dartford, Kent
Bike: M900ie
Posts: 7,241
It would be a water temperature sensor on S4's, but just a temperature sensor on aircooled bikes like the 620/900ie.

See if you can borrow one of another injected bike (either 900 or 1000ie) and swap them over, as this is what Dave did on mine - borrowed Fatblokes sensor from his 1000ie. If the bike runs ok you've sussed it and need to buy a replacement - about £50.

BTW Dave test metered both mine & FB's sensors and got the same reading from both?? But my engine would only run right using a replacement switch so the original was deffo knackered - did about 18,000 miles.
__________________
GT
Fully paid up member of the S.A.S. (Scottoiler Appreciation Society) 27,000 miles on original chain - and still going strong!

Last edited by gary tompkins; 05-09-2005 at 12:03 AM..
gary tompkins is offline   Reply With Quote
Old 20-06-2007, 07:50 PM   #10
The Kevlar Kid
Guest
 
Posts: n/a
Just had this trouble on mine... guess what - it's a 2001 model year 900ie

As Gary says, most places want about £50 for this, but there are some cheaper alternatives (that also carry it in stock) e.g. Demon Tweeks do one for about £33.

I got mine (a genuine Webber / Marelli part) from 'Southern Carburetters and Injection' for £29.24 inc vat and very fast recorded delivery. This was the cheapest I could find for a quality / OE replacement.
  Reply With Quote
Old 20-06-2007, 09:26 PM   #11
Rockhopper
Guest
 
Posts: n/a
Get it hooked to a mathesis tester at your local ducati service persons place and they will tell you exactly whats wong. Saves the hassle of swapping bits that may not be faulty in the first place.
  Reply With Quote
Old 21-06-2007, 12:18 AM   #12
The Kevlar Kid
Guest
 
Posts: n/a
Looks like this is a particular problem with this year of bike...

Symptoms are exactly as Gary describes - so it was a bit of a no brainer to give it go.

£30 for a new sensor is probably cheaper than Ducati will charge for just testing the system.
  Reply With Quote
Old 21-06-2007, 07:49 AM   #13
squiffything
Guest
 
Posts: n/a
Problem sounds very much like the one I have at the mo black spark plugs when changed, hard to keep running on tickover and sounds as rough as a butchers dog. Still pulls well when revved but terrible at slow speeds/low revs.

BG let me know how it goes.
  Reply With Quote
Old 21-06-2007, 06:49 PM   #14
The Kevlar Kid
Guest
 
Posts: n/a
Squiffything - BlueGuzzi had this problem ages ago - this is an old thread. Sounds like you have the same prob though.
  Reply With Quote
Old 22-06-2007, 08:12 AM   #15
squiffything
Guest
 
Posts: n/a
I didn't notice the date of the original thread you blended your reply in so well.

It's due in for a service and MOT next week so I may let the Mechanic have a look then again it might be worth ordering the bit from S C & I and have the replacement done while they do the service. Do you have the part number or description that I can quote when ordering? Also would it be the same bit for a 620ie I note yours is a 900
  Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT. The time now is 11:22 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.