UK Monster Owners Club Forum » .: Technical :. » Engines, Clutch, Gears » Idle Speed Adjustment On Monster S4

Reply
 
Thread Tools Display Modes
Old 25-10-2006, 05:56 PM   #1
BREEKO
Guest
 
Posts: n/a
Idle Speed Adjustment On Monster S4

hi, please help me to adjust the idle speed on my monster S4 2001. i need to know the correct idle speed and where the ajdustment screw is and what it looks like. if someone has any pics that would help. thanks.....
  Reply With Quote
Old 25-10-2006, 06:20 PM   #2
Scotty
Guest
 
Posts: n/a
computer adjustment isnt it ?
or maybe you could mess with the fast idle lever bit on t' throttel bodys ~:?
  Reply With Quote
Old 26-10-2006, 09:19 PM   #3
MotoNik
Bronze Member
 
MotoNik's Avatar
 
Join Date: May 2003
Location: Sherbourne
Bike: M600
Posts: 401
I've just had my Supersport injection in at Rapido to get the idle speed sorted - it was idling too low. Turned out that the throttle position sensor needed re-setting - it was reading too high.

Prior to that I had manually adjusted the throttle stop screw to bring the idle up a bit. It's located on the throttle side of the bike, and assuming your throttle bodies are the same (or similar) to mine you should be able to locate the throttle cable "cam" just inside the frame.

The throttle stop shouldn't be confused with the fast idle stop - you need to check which bit the throttle cable is connected to, and make sure you get the throttle stop and not the fast idle ("choke" if you like).

On my bike the throttle stop can be adjusted by turning a little grub screw, which is sealed with paint when it's set at the factory. I hooked the paint out of the grubscrew allen socket and tweaked it until the idle speed was correct.

The problem wasn't properly sorted until I had the fuel injection checked and corrected by a dealer though - they had to plug it in to their Mathesis computer, which allow diagnosis of sensors, throttle position setting etc. Assuming it just needs re-setting it probably won't cost very much.

Hope that helps,

Nik
MotoNik is offline   Reply With Quote
Old 27-10-2006, 05:53 PM   #4
BREEKO
Guest
 
Posts: n/a
thanks guys, looks like a trip to a ducati dealers.
  Reply With Quote
Old 28-10-2006, 07:10 PM   #5
Shauns4
Guest
 
Posts: n/a
The idle speed can be adjusted by the throttle stop screw, I can send a diagram if needed. However, normally the stop position is set measuring the angle or voltage output from the TPS and then the idle speed is trimmed by using the air -bypass screws, this is how I set mine and ticks over perfectly.

If the engine ticks over and picks up smoothly then just adjust the stop to get the correct idle speed (easy), if it is eractic or rough then it's best to check the TPS setting, vacuum balance of the throttle bodies, stop position and then trim the idle with the by-pass screws....(not so easy).

Shaun
  Reply With Quote
Old 28-10-2006, 08:58 PM   #6
Stafford
P3, nice.
 
Stafford's Avatar
 
Join Date: Jun 2006
Location: Calne
Bike: S2r 1000
Posts: 2,145
What is the suggested tick over speed?
Cheers
Quarx
__________________
celeres-racing.blogspot.co.uk/

The probability of survival is equal to the angle of arrival.
Stafford is offline   Reply With Quote
Old 29-10-2006, 07:08 AM   #7
Shauns4
Guest
 
Posts: n/a
Quote:
Originally Posted by quarxuk
What is the suggested tick over speed?
Cheers
Quarx
about 1100 rpm
  Reply With Quote
Old 29-10-2006, 03:55 PM   #8
Stafford
P3, nice.
 
Stafford's Avatar
 
Join Date: Jun 2006
Location: Calne
Bike: S2r 1000
Posts: 2,145
Thanks for that, I'm spot on then.
Cheers
Q
__________________
celeres-racing.blogspot.co.uk/

The probability of survival is equal to the angle of arrival.
Stafford is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT. The time now is 11:42 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.