Register | FAQ | Members List | Calendar | Today's Posts | Search | Contact |
|
Registered
Members: 636 | Total Threads: 50,821 | Total Posts: 518,483 Currently Active Users: 1,058 (0 active members) Please welcome our newest member, jaraduke |
|
|
Thread Tools | Display Modes |
|
08-10-2017, 07:17 PM | #1 |
Guest
Posts: n/a
|
Cam belt tensioners
Has anyone had experience of aftermarket cam belt tensioners?
I just changed the belts on mine, and one movable tensioner was seized solid, don't know how long it had been like this, but the belt wasn't too bad, it had just gone all polished and shiny on the rear of it! (and that is after three years and about 15,000 miles since last change). I couldn't get the bearing off the housing, so I thought, don't bugger about, change the lot. As the bearings wont come off the holder, I need the housed bearings which look to be a single double-width bearing now, not the double-single bearings as fitted to my bike. Ebay lists kits from Germany around the £180 - £200 mark for the two movable and the two fixed bearings delivered, but they are aftermarket bearings. Has anyone DIY'd the bearing change, or does everyone just get Luigi to do it!! |
08-10-2017, 07:31 PM | #2 |
Fanactical volunteer
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,033
|
The double bearing ones are £5 each bearing roughly and not cheaply ones I just changed all of mine but the tall tensioner ones were OK. They are the same as the clutch pressure plate ones
__________________
http://albies93m900.blogspot.co.uk/ |
08-10-2017, 08:21 PM | #3 |
Guest
Posts: n/a
|
Hi Albie, the two movable ones are pretty shot, the seized one won't come off at all, and the good one will probably need to be destroyed to release the bearings from the shaft (two days of soaking/bashing and pressing hasn't budged it!). I concluded that the complete thing needs replacing. It would be great if I could get away with just replacing the bearings, but the holder is shot, so I'm biting the bullet and changing the lot.
I was just wondering if anyone had experience of aftermarket kits from ebay. |
08-10-2017, 09:25 PM | #4 | |
Fanactical volunteer
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,033
|
Quote:
__________________
http://albies93m900.blogspot.co.uk/ |
|
08-10-2017, 10:25 PM | #5 |
Guest
Posts: n/a
|
Yeah, I get that, it would be a nice saving to just change the bearings, but an expensive mistake if the refitted bearings broke down due to my ham fisted attempt at fitting them.
For the record, I've changed lots and lots of bearings bushes etc - most recently rebuilding an ancient Montesa 315R rear linkage and swingarm bushes/bearings which was no picnic, but these tensioner bearings seems a lot more stubborn. They've been in there for 11 years... |
08-10-2017, 08:01 PM | #6 |
.
Join Date: May 2007
Location: Stockbridge
Bike: M900
Posts: 1,984
|
Hi Bigxr: how are things at the dirty castle?
If you read the codes off the bearings you can get SKF or other quality replacements far cheaper than Ducati prices.
__________________
Original and Best since 1993 |
08-10-2017, 08:24 PM | #7 |
Guest
Posts: n/a
|
Hey Darkness, Caerfilfy is fine, I need the complete assembly not just the bearings, I wish it wasn't so. :-(
|
09-10-2017, 06:53 AM | #8 |
Fanactical volunteer
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,033
|
No worries I understand
Most may I say that loosely by dealers anyhow but seeing I was doing a complete engine overhaul wanted to try and changed myself
__________________
http://albies93m900.blogspot.co.uk/ |
09-10-2017, 11:52 AM | #9 |
Guest
Posts: n/a
|
My main problem is how to "launder" the cost without her-who-should-be-obeyed finding out!!
(Nice 900 by the way. ) |
09-10-2017, 12:29 PM | #10 |
Guest
Posts: n/a
|
This advice may be too late now but the Clarke bearing pullers from Machine Mart do work well. This is on my M1000 which is same as S2R
As you bolt the two halves together the wedge action initially pulls the bearing along the shaft so the two halves can be closed more and get behind the bearing. If you do take your bearing to a supplier do make sure the new bearings comply with the SKF suffix 'LHT23' which means the grease is good for up to 150°C .....and I assume you have removed the circlip? |
09-10-2017, 03:53 PM | #11 |
No turn left unstoned
Join Date: Jun 2010
Location: leicester
Bike: M750
Posts: 4,546
|
Nope .. never too late.
My 750 is running on 25k old bearings and I intend to change them before it hits 30k. I shall now be nipping by Machine Mart next time I'm out to pick up one of said pullers. Ta. Having looked at your pics, I might also consider making some kind of centralising button to go between the end of the spigot and the puller bolt. ps. I notice they do two sizes .. 30-50mm and 50-75mm. Which one did you use ? I'm guessing that the smaller one is big enough ? Last edited by utopia; 09-10-2017 at 03:57 PM.. |
09-10-2017, 04:56 PM | #12 |
Lord of the Rings
Join Date: May 2013
Location: Norwich
Bike: M900sie
Posts: 5,848
|
But there are two pullers in use there, aren't there?
A circular one and a three legged one. I notice that the split circular one has two opposed threaded holes, which look like they could be used with a device much like a clutch cover puller to give a straighter pull. Does something like this come with the puller? Or is one left to one's own invention?
__________________
|
09-10-2017, 06:03 PM | #13 |
Guest
Posts: n/a
|
|
09-10-2017, 12:16 PM | #14 |
Fanactical volunteer
Join Date: Oct 2003
Location: Kent
Bike: M900
Posts: 9,033
|
Thanks btw lol. This is just a service cost like your car. It's in the interests of having something devalued or worth more if serviced and running. My missus is ok she believes in me creating good
__________________
http://albies93m900.blogspot.co.uk/ |
09-10-2017, 05:46 PM | #15 |
Guest
Posts: n/a
|
how much from the dealers ?
moto rapido quoted £75 for the whole assembly for my evo. |
|
|