UK Monster Owners Club Forum » .: Technical :. » Mods & How To's » Quiet Clutch Mod

Reply
 
Thread Tools Display Modes
Old 31-03-2020, 08:45 AM   #1
The Clockie
Guest
 
Posts: n/a
Quiet Clutch Mod

Here's the piece I wrote for the Ducati ST group years ago. It has been very well tested by me and many owners in that group, and word has spread beyond too. I don't claim that I invented it, but none of those seeking to sell parts ever explained it, hence my write-up.

Last edited by slob; 31-03-2020 at 08:55 AM..
  Reply With Quote
Old 31-03-2020, 08:56 AM   #2
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
A quiet Ducati clutch, the easy way!
By Nick Woods

The following modification is based on my experiences with a ‘99 ST4 clutch, initially using an OEM basket and centre/hub plus an aftermarket plate pack, and subsequently an OEM centre and Charlie Smith/Procutting clutch basket with matched Barnett plate pack.

It also works very well on a Cagiva Gran Canyon (904 Ducati motor) that had a rather loud clutch rattle as received.

Other members of the Yahoo (now Groups.io) LiST have tried it with success, but we have not researched into whether it can be applied to every possible combination of OEM and aftermarket components. It is important, therefore, that you understand the principles before starting work. As with any modification, there are always pros and cons, so you do it at your own risk!



Ducati’s dry clutch has good ‘feel’ and works well, its one main advantage over the wet clutches of other manufacturers being that dust from the friction linings does not contaminate the oil. Theoretically, the absence of friction-reducing oil might also make it possible to use lighter clutch springs, but no Ducati rider has ever seen evidence of that! Given there is no need to keep oil inside the unit, it can be run open to cool it and give it a racier look, but that is when its major attribute becomes really evident. It is loud!!

Not a problem when the engine is actually driving the rear wheel, a heavy knocking noise is apparent when idling in neutral, and is sufficient to be quite offensive to those of a sensitive nature. (We shall ignore riders who proclaim that ‘loud clutches save lives’, as they are confused souls…) Whether the noise is objectionable or not, that mechanical mayhem does no good to the clutch itself, such that some owners prefer to ride the bike gently as it warms up, rather than let the clutch hammer itself apart.

The noise is directly related to the dry status of the Ducati clutch, as there is no oil film to cushion necessary play in the unit. The infrequent and uneven power pulses from the beloved vee-twin also make it worse than would be the case with a four-cylinder engine, plus the Ducati is sports-orientated and does not carry a massive flywheel that would damp the pulses better.

The knocking actually comes from the clutch plate-pack rocking to and fro in the slots of the clutch basket. The closer the clearances, as with the fabled Charlie/Barnett set-up, the quieter the unit, and having alloy tabs running in alloy slots is less resonant than with the original steel on steel. However, sooner or later, the clearances will open up with normal wear, and the knocking starts in ernest.

Several commercial suppliers have hit on a method of preventing the to-and-fro fretting of the plate-pack in the basket, and the method outlined below is based on personal experience of one of them which utilised a special plate pack mated to the OEM ST4 basket and centre. The difference with the quietening mod that follows is that it requires nothing more than the addition of one or two old friction plates, and no machining or special components at all.

Basically, it consists of incorporating the equivalent of a rotary friction damper to bind the entire clutch unit together, (centre, plate-pack and basket) when the clutch is fully engaged. It has no effect on clutch action, but there are some theoretical mechanical/wear disadvantages that possibly explain why Ducati themselves have not adopted it, though there is some evidence that they did utilise it at one stage of 900 production, perhaps also with the Paso, but they subsequently abandoned it.

I’ll outline the theoretical disadvantages later but, rest assured, clutches modified in this way have given many thousands of miles of trouble-free silent service.

Last edited by slob; 31-03-2020 at 08:58 AM..
slob is offline   Reply With Quote
Old 31-03-2020, 09:00 AM   #3
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
So, a step by step procedure that can produce a quiet clutch in minutes is as follows. I assume that all home Ducati mechanics are able to gain access to the clutch and remove and replace the plate-pack correctly. For this job, there is no need to remove either the clutch centre or the basket, both of which require special tools.

Before you start, you will need to find one or two old friction plates, preferably of the OEM ST2/ST4 steel type, as they are stiffer than the alloy friction plates of the OEM ST4s.



1: Remove the pressure plate and springs, and take all the loose plates out, keeping them in the order of removal. Inspect the edges of the tabs on the friction plates, and the sides of the basket slots. There, you will likely see the wear caused by the tabs slamming to-and-fro in the slots. If the slots have deep notches in them, a new basket may be needed in the near future, or smooth engagement could be compromised by the tabs sticking in the grooves. There is nothing to be gained by filing the burrs off the tab sides, as this just reduces the contact surface-area again.


2: Drop one of the old junk friction plates into the basket first, pushing it right down into the slots. As the tabs on the plate reach the radiussed ends of the slots, they will lock into the curve while pressure is applied, and cannot rattle to-and-fro. This is the first significant aspect of the mod.


3: Then add the second old tabbed friction plate.


4: Now slide the first plain steel plate onto the clutch centre and push it as far in as it will go. For the quietening mod to work, that steel plate has to contact the face of the previous friction plate before it hits the bottoms of the splines/slots on the centre. The amount by which the friction face protrudes needs only to be around 0.020”/0.5mm, and more will not be better. This dimension will likely be different with the various options of OEM and aftermarket components you might be using, and is also influenced by any wear on the front face of the clutch centre. Checking the amount of overhang will require a short straight-edge that can be laid across the friction faces adjacent to the roots of the slots in the centre. It may be that sufficient overhang is provided by only one extra friction plate, though this dimension will likely diminish as the tabs bed into the basket slots with use.


5: Replace all the other plates as they came out, including the cone-shaped spring-plate, whose exact position and orientation does not seem to be critical. (Note that the wave-profiled spring plate in the Barnett plate-pack gives more resilience, and may be a factor in abolishing the famous ‘groan’ on take-up. Refacing your stock plates can apparently work too).



6: Disregarding the extra one or two plates in the bottom of the basket, your effective plate-pack thickness should only have increased by that 0.020”/0.5mm mentioned in 4 above. This should mean there will be no issues with plates coming out of the basket slots or off the centre when the clutch is disengaged, especially if your plates have seen some use. However, you should check this before running the bike. The specified max thickness of the pack is 38.5mm, but a mm or so less is permissible.

If you have to juggle with plates, remember that different brands vary in thickness and number, and I see no problem with mixing-and-matching plates to get the right total thickness. If you find it difficult to get down to the 0.020”/0.5mm overhang, you could always reduce the thickness of the friction material on the additional plates, but do it evenly on a flat surface to keep the outer surface square to the rest of the components. Finally, make sure that the very last plate you put in is a plain steel one for the pressure plate to contact.
slob is offline   Reply With Quote
Old 31-03-2020, 09:02 AM   #4
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
7: With the clutch back together, and the springs seated and tightened carefully, test the action without the engine running:-

A: Pull the clutch lever right in with one hand, and then gently rock the pressure plate with the finger-tips of your other hand. You should see that all items (pressure-plate/centre, plain plates, friction plates and basket) are free to move independently, within their limits of play.

B: Now start releasing the lever while still rocking to-and-fro. You will see the pressure-plate and all the plain and friction plates start to bind and move as one, but that unit will still rock within the slots of the basket.

C: As you let the lever out finally, you should see that the whole unit goes solid, such that the tabs will no longer rock within the basket slots. Any remaining movement is now inside the gearbox.


8: Replace the clutch cover and start the engine in neutral. Silence!!

Now test-ride the bike with caution to check that you can find neutral as easily as before. The dimensional change with this mod should be compensated by the hydraulic actuation, but there will be slightly more lost motion as the plates bed and flex a little. If you have a problem, either abandon the mod or check ways of increasing clutch lever travel by incremental adjustment of the lever screw (Caution!), bleeding the hydraulic line or bending the lever blade out.




Now to the theoretical drawbacks of this mod.


A proportion of the clutch spring end-loading is now being transferred to the basket, which means that the bearing in the back of the clutch basket mount is seeing an unfamiliar endload.

In addition, action and reaction results in loading of the alloy clutch centre against its steel retaining washer, which interface is dry. The clutch centre incorporates the cush-drive rubbers that smooth the power pulses, especially at low speed, and this loading could reduce the effectiveness of the cush mechanism and accelerate wear at this point. Personally, I can detect no difference in the feel of the power pulses before and after the mod, but there will be more wear as the centre and retainer fret against each other. Perhaps a PTFE shim at this point might be a good idea.

I feel the wear issues are genuine, but doubt that they are significant. Many Ducati riders have covered substantial mileages using one form or another of this modification without problems, and I’m sure all would agree that the silence and reduced wear on the clutch tabs and slots are well worth the risk. In any case, it will take only minutes to revert to standard, should you come to decide otherwise.

Please note that this is simply free advice from an owner/rider, and you make this mod at your own risk.


Nick Woods,
Norfolk, UK,
May 2006, revised Feb 2020.
slob is offline   Reply With Quote
Old 31-03-2020, 12:30 PM   #5
The Clockie
Guest
 
Posts: n/a
Thanks Rob. I had to take advice from the Missus to put it into a form that the site would accept, but you beat me to it!

Nick
  Reply With Quote
Old 07-04-2020, 08:11 PM   #6
Luddite
Registered User
 
Luddite's Avatar
 
Join Date: Aug 2011
Location: Southampton
Bike: M1100evo
Posts: 2,465
An interesting alternative quiet clutch mod here. Not as cheap or satisfying as Nick's diy version but interesting to hear the before and after sounds nevertheless:



YouTube address in case the button doesn't work... https://www.youtube.com/watch?v=ldW6kMoob2s

(PS thanks for the new button, Rob! )

Last edited by Luddite; 07-04-2020 at 08:29 PM.. Reason: Wrong YouTube reference used
Luddite is offline   Reply With Quote
Old 07-04-2020, 10:10 PM   #7
The Clockie
Guest
 
Posts: n/a
A Belgian guy also made a kit with extra bits that dropped into the drum like the system in the video.

DrDesmo's quiet plate pack was essentially the same as the process I described, utilising the slots in the drum as the loading point, but of course he didn't explain how simply the same effect could be achieved with your original bits plus a gash plate or two.

Simple is good!

Nick
  Reply With Quote
Old 08-04-2020, 10:14 AM   #8
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,091
Quote:
Originally Posted by The Clockie View Post
A Belgian guy also made a kit with extra bits that dropped into the drum like the system in the video.

DrDesmo's quiet plate pack was essentially the same as the process I described, utilising the slots in the drum as the loading point, but of course he didn't explain how simply the same effect could be achieved with your original bits plus a gash plate or two.

Simple is good!

Nick
Cheap and simple is even better. You could then put the 100 euros towards a better quality clutch!
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 08-04-2020, 12:42 PM   #9
The Clockie
Guest
 
Posts: n/a
Quote:
Originally Posted by Darren69 View Post
Cheap and simple is even better. You could then put the 100 euros towards a better quality clutch!
A clutch is a clutch: what else do you expect it to do beyond engaging smoothly and not slipping?

To be honest, I don't recall much difference between the original steel drum and plates and the new all-alloy one I put on the ST4. The motor might have spun up a fraction faster but that wouldn't make much difference with the sedate way I ride. A slipper clutch would similarly be lost on me but I admire the Men who need one!

Nick
  Reply With Quote
Old 08-04-2020, 05:52 PM   #10
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,091
Quote:
Originally Posted by The Clockie View Post
A clutch is a clutch: what else do you expect it to do beyond engaging smoothly and not slipping?

To be honest, I don't recall much difference between the original steel drum and plates and the new all-alloy one I put on the ST4. The motor might have spun up a fraction faster but that wouldn't make much difference with the sedate way I ride. A slipper clutch would similarly be lost on me but I admire the Men who need one!

Nick
You might actually be surprised on how much nicer they are to ride with a slipper. You say you don't need one and I used to think the same until I fitted one to my 748 and I was so impressed and surprised when I could feel it working when downshifts weren't exactly spot on that would unsettle the bike, I got one for the S4 too.

I mean you can ride them and downshift without the manual clutch if you want aswell they just have to work harder/wear quicker but I always use the clutch as I would normally but either way it takes all the stress out of the engine/gearbox and drivetrain and the bike is rock steady.

There are a few downsides however as servicing is a little bit more involved and you can no longer bump start, but who can do that anyway?

Ally basket and plates is worth doing if only to stop the ringing noise you get with a steel basket and they do spin up a bit faster and roll on acceleration is better; even more with a light flywheel.

There was a guy on ebay Italy 'Desmoinside' selling new DP SBK '08 versions for £400 which is a really good price, if you can find one. It's one of the best mods I've done and one which I would certainly recommend and do again.
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 09-04-2020, 08:59 AM   #11
The Clockie
Guest
 
Posts: n/a
Darren,

I can see your argument re slipper clutches but would respectfully submit that the only reason to ride a 748 is to go like merry hell, banging gears in at great speed! I've dabbled very slightly with vee-twin sportsbikes but know they aren't my style at all, at least not on the roads around here, so am content to take time in making good manual gearchanges with clutch and throttle synchrony.

Which is not to say I wouldn't like to have a Ducati sportsbike in the garage to admire! I seriously test-rode an 888 a few months ago, meaning to invest a lot of money (for me) in a real classic Ducati, but I didn't gel with it at all. The S4R is much more me, especially after spinning the 'bars somewhat to give a flatter wrist angle. First time I've come across pegged brake and clutch levers: the cheek of manufacturers to try to dictate a rider's ergonomics!

Nick
  Reply With Quote
Old 09-04-2020, 11:20 AM   #12
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,091
Quote:
Originally Posted by The Clockie View Post
Darren,

I can see your argument re slipper clutches but would respectfully submit that the only reason to ride a 748 is to go like merry hell, banging gears in at great speed! I've dabbled very slightly with vee-twin sportsbikes but know they aren't my style at all, at least not on the roads around here, so am content to take time in making good manual gearchanges with clutch and throttle synchrony.

Which is not to say I wouldn't like to have a Ducati sportsbike in the garage to admire! I seriously test-rode an 888 a few months ago, meaning to invest a lot of money (for me) in a real classic Ducati, but I didn't gel with it at all. The S4R is much more me, especially after spinning the 'bars somewhat to give a flatter wrist angle. First time I've come across pegged brake and clutch levers: the cheek of manufacturers to try to dictate a rider's ergonomics!

Nick
Pegged, really? Are they on the bars or the clamps? I never knew and I don't think mine were, although I do recall there were some monster specific master cylinders with the mirror boss in the centre of the clamp part and not on the top of it, and then they had been rotated 45 degrees so the centre of the clamp part was on top. If that makes sense?
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Old 09-04-2020, 11:46 AM   #13
slob
.
 
slob's Avatar
 
Join Date: Jul 2003
Location: East London
Bike: Multiple Monsters
Posts: 9,733
They’re not (IIRC) it’s just the switchgear and twistgrip but not ergonomically great if you move the levers and then have to stretch to the switches.
slob is offline   Reply With Quote
Old 09-04-2020, 06:29 PM   #14
Darren69
Transmaniacon MOC
 
Darren69's Avatar
 
Join Date: Sep 2013
Location: Sutton In Ashfield
Bike: Multiple Monsters
Posts: 6,091
Quote:
Originally Posted by The Clockie View Post
Darren,

I can see your argument re slipper clutches but would respectfully submit that the only reason to ride a 748 is to go like merry hell, banging gears in at great speed! I've dabbled very slightly with vee-twin sportsbikes but know they aren't my style at all, at least not on the roads around here, so am content to take time in making good manual gearchanges with clutch and throttle synchrony.

Which is not to say I wouldn't like to have a Ducati sportsbike in the garage to admire! I seriously test-rode an 888 a few months ago, meaning to invest a lot of money (for me) in a real classic Ducati, but I didn't gel with it at all. The S4R is much more me, especially after spinning the 'bars somewhat to give a flatter wrist angle. First time I've come across pegged brake and clutch levers: the cheek of manufacturers to try to dictate a rider's ergonomics!

Nick
Now then before we get into this; is the S4/R Monster actually a sport bike or not? Ducati called them Hypermonsters but I would argue that it is actually a thinly disguised sports bike although its not a race rep, but what you have essentially is an 888 derived frame and chassis, suspension and a 916 or 996 engine with a close ratio 748 gearbox. That's a sportbike with some pedigree if you ask me. OK so it's more sit up than the race rep bikes and with the standard setup they give it, it's a scary wheelie bound thing that is unsettled everywhere if you try to push it. But...

It's an 888 rolling chassis modified with a stiffer frame so if you dial the thing in and do a few mods it can really handle, ok so not in the 748/916 bracket but can be nearly as planted and stable mid corner just more comfortable. If I were doing another upgrade on mine iright now it would be the ST4S or S4R engine with the S4R gearbox. But for now it has more than enough grunt really, well more than a standard 916 actually. So I can only imagine the S4R is even more awesome?

So there is really two flavours to them. Hooligan wheelie thing that will scare the crap out of you or sweet handling sportbike that would give a 888 or 916 rider a surprise
__________________
Roast Beef Monster!

Termignoni and Bucci - Italian for pipe and slippers!

S4 Fogarty, S4R 07T, 748, Series 1 Mirage
Darren69 is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:24 PM.

vBulletin Skins by vBmode.com. Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.