|
Brakes & Wheels
Recent model 900 SS bikes have the same size front brake disc rotors (320mm) as the Yamaha XJ1200, FZR1000 Exup and Genesis, YZF1000, FZR 750 Genesis, SZR 660 and TZR 250 but check that the Yamaha carriers have the same offset as the Ducati carriers.
Spiegler floating brake discs 300mm, are the same for: Yamaha TRX 850, 4KN, 4UN, TDM 850, 3VD, 4CM, FZR 600, 3RH, 3HE, FZR 600 R, 4JH / MH / MM. Once again, check that the disks have the same offset as the Ducati carriers
Ducati 907ie Brakes, ZDM906PI2, 900SS Bj. 88-90, ZDM906SC, Moto Guzzi 1000 Daytona Type KL.
Brembo front brake handlebar assembly - Yamaha FJ1200/FZR1000, Kawasaki ZX7-6 (Nissan remote reservoir, 5/8 inch (15.9mm) part number 43015-1392), Suzuki GSXR 750/1100 1990 to 1996, Honda CBR 900.
Grimeca 180 mm double-sided front drum brake from the early Benelli 250 2C (or equivalent Moto Guzzi 250) is the same as the later Ducati singles. The lugs on the fork where the torque arms engage appear to be identical to those on the early Ducati forks (the one with metal gaiters of the MK3 and the one with rubber gaiters of the SCR). Since the bolts that hold the mudguard are very small (6 mm) the torque arms embrace the aluminium lug behind the bolt and are kept in place by the mudguard's lugs.
Paso speedo drive hub: same as Aprillia RS125.
WHEEL BEARINGS - for 18 inch Borranis and FPS alloy mags
SKF 63004-2RS (size 20 42 16)
BRAKE PADS for F08: (Brembo) D=07.2256.30
Galfer 013 G1532
Carburettors and fuel system
Parts for Mikuni 38 mm constant pressure carburettors mounted on current Ducati models such as the Monster or Supersport are also available at Yamaha dealers because the TDM 850 uses the same. Rubber inlet "pipes" for the carb to manifold junction on the 750F1 or 36 mm
89 900 and Paso with Webber carburetor, parts and overhaul kits are available from auto shops, also high velocity air filters to replace the standard air boxes well as the small filter to fit the crankcase breather.
Paso Dellorto carb conversions. Ski-Doo/Bombadier Snowmobile part # 570-134600 is a near perfect match, the important internal "rubber washer" that mates the carb and manifold is spot on.
888 engine speed and position sensors - Fiat Tipo SEN 8D
907 ie. throttle position sensor (potentiometer), type PF09, is also used in Alfa Romeo 33 ie
Fuel pumps: Ducati 888 item made for Ducati by Walbro (their part number 5CA305-3 (or 5CA305-2 for the white box).
906 Paso: Facet FSE574A. 907ie: Bosch part number: 0 580 463 999.
Clutch
Bevel friction plates - Suzuki GSF400
Clutch hub bearing: 6201 32 x 12 x 10 (OD, ID, thick). Get a 2RS/1C3. It's a standard electric motor bearing, sealed on both sides.
Clutch slave piston seal: "Quad Ring" part number Q4210-560ND I believe that they need to be made of ethylene propylene (EP).
There is also a Honda part that will fit, part number: 06431-MA3-405. Sorry, I have no information as to which model it is from, it is a square-section seal.
Clutch thrust bearings: If you have a dry clutch with a 28.5 mm diameter piston fitted with a ball race for the thrust bearing, you will probably find that SKF bearing 630/8-2RS1 will fit, sizes are:
Outside diameter: 22 mm
Inside diameter: 8 mm
Width: 11 mm
|