Ducati Performance Alloy Exhaust + Hi High level link Pipes + carbon heat guards

[Dirty]

Ducati Performance Alloy Exhaust + Hi High level link Pipes + carbon heat guards

For 900, 600, 750

What it says on the tin (and in the pictures :) )

I bought these from a member on here with the intention of cutting them down but plans change and they are surplus to requirements. I paid £125 for them so that's what I'd like. Postage extra or collect from SE London

They are in pretty good nick. Obviously not without a few marks here and there, mainly where the straps rub but you won't see that and anyway nothing that wouldn't polish out with a bit of cdo and elbow grease. I think there is 1 brass colet thing missing from the carbon heat guards but it doesn't notice. I'll let the pics tell the story.

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164043.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164102.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164104.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164058.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164140.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164150.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/0245c24c-6ef9-4295-a20e-f101df7a8c53.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/for%20sale/2013-09-25164054.jpg

[Mick b]

Would these fit a 620ie ? If so I will have
them of you

[Dirty]

Now sold :ukm:

[Blah blah]

Didn't keep them very long then...

[Darren69]

Was gonna say, somebody on here wanted something similar, Termis for a 620 I think . Long shot, but i don't suppose you know if you can get the fibre washers and other bits anywhere?

[Dirty]

Didn't keep them very long then...

5 months roughly! but they've gone to a good home now, as far as I know there are no plans to cut them up like I had!

Once I saw PaulR's road race under engine exhaust I decided something along those lines (small, almost hidden) was my ultimate aim. Then I started to question the wisdom of putting time effort and money into a system that was just temporary. With that in mind I decided you were right it was a shame to cut up a perfectly good set of cans.

Depending on how the new set up goes I might end up selling my Ti set at some point too.

[pompone]

Did a comment get cancelled?

[Dirty]

Nope, don't think so? Why, you been posting drunk again :)

[Dirty]

I don't suppose you know if you can get the fibre washers and other bits anywhere?

I don't know sorry

[Darren69]

Was a long shot I know, must be somewhere though. If I only knew what was missing it would be a start, I just have v short bolts holding mine one :(

[Albie]

Was gonna say, somebody on here wanted something similar, Termis for a 620 I think . Long shot, but i don't suppose you know if you can get the fibre washers and other bits anywhere?

Go to any decent bolt fasteners shop, ironmongers for them or ebay. http://www.ebay.co.uk/bhp/fibre-washers

[Dirty]

I'll take a pic and post it here tomorrow

[Dirty]

Go to any decent bolt fasteners shop, ironmongers for them or ebay. http://www.ebay.co.uk/bhp/fibre-washers

It's the little brass colet thing I found hard to source

[Darren69]

Pics and sizes of the bits would be useful,thanks

[Dirty]

Pics and sizes of the bits would be useful,thanks

Sorry it took so long mate. Lost my short engineering ruler, still can't find it!

Anyway here's pics n sizes

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zps046d7636.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/6649e6b9-147e-463b-9403-f076941ad1d5.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zpsb8b29a75.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zps848a041a.jpg

[utopia]

Darren, I could make you a set of the top-hat bushes if you can't get hold of any.
In stainless, ally or whatever.
Would have to make a small charge, but it wouldn't be too silly.

[Darren69]

Thanks I may take you up on that kind offer. I'm wondering if they are similar to the top hats on the headlamp subframe as I may have some somewhere.

[Darren69]

Sorry it took so long mate. Lost my short engineering ruler, still can't find it!

Anyway here's pics n sizes

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zps046d7636.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/6649e6b9-147e-463b-9403-f076941ad1d5.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zpsb8b29a75.jpg

http://i312.photobucket.com/albums/ll350/Alf230202/Duke/fasteners/null_zps848a041a.jpg

Thanks for the pics thats really helpful

[Darren69]

Darren, I could make you a set of the top-hat bushes if you can't get hold of any.
In stainless, ally or whatever.
Would have to make a small charge, but it wouldn't be too silly.

Could you clear your inbox Jeff, ta

[utopia]

Inbox cleared.